Summary
- Open the glove box and locate the two screws holding the lid in place.
- What if I can’t find the screws holding the glove box lid in place.
- What if I need to remove the glove box for a more complex repair.
Are you looking to access the wiring behind your glove box in your 2019 Ram 2500? Maybe you need to replace a faulty component or simply want to install an aftermarket accessory. Whatever the reason, removing the glove box can seem daunting, but it’s actually a fairly straightforward process. This guide will walk you through each step, making the task easy and stress-free.
Tools You’ll Need
Before you begin, gather the following tools:
- Phillips screwdriver: This is essential for removing the screws holding the glove box in place.
- Small flathead screwdriver or pry tool: This is helpful for gently prying off trim pieces and releasing clips.
- Protective gloves: These will protect your hands from any sharp edges or dirt.
Step 1: Disconnect the Battery
Safety first! Disconnect the negative battery terminal to prevent any electrical shocks while working on the car’s electrical system.
Step 2: Remove the Glove Box Lid
Open the glove box and locate the two screws holding the lid in place. These are usually located on the top edge of the lid. Use your Phillips screwdriver to remove these screws.
Once the screws are removed, gently lift the lid off the glove box. There may be clips holding the lid in place, so you might need to use your flathead screwdriver or pry tool to release them.
Step 3: Remove the Glove Box Assembly
With the lid removed, you can now access the glove box assembly itself. Locate the screws holding the assembly to the dashboard. These are typically found on the sides and bottom of the glove box.
Use your Phillips screwdriver to remove these screws. Once removed, you can carefully pull the glove box assembly out of the dashboard. Be mindful of any wiring or connectors connected to the glove box.
Step 4: Disconnect Wiring and Connectors
Before completely removing the glove box assembly, you need to disconnect any wiring or connectors attached to it. These connections are usually located on the back of the assembly.
Carefully disconnect each connector by pressing the release tab on the side of the connector and gently pulling it apart.
Step 5: Remove the Glove Box Assembly
With all wiring and connectors disconnected, you can now completely remove the glove box assembly from the dashboard.
Step 6: Reinstall the Glove Box Assembly (Reverse Steps)
Once you’ve completed your work, you can reinstall the glove box assembly by following the steps in reverse order.
1. Reconnect the wiring and connectors: Make sure each connector is securely attached.
2. Reinstall the glove box assembly: Align the assembly with the dashboard and carefully push it back into place.
3. Reinstall the screws: Secure the assembly with the screws you removed earlier.
4. Reinstall the glove box lid: Align the lid with the glove box and secure it with the screws.
5. Reconnect the battery: Once the glove box is reinstalled, reconnect the negative battery terminal.
Final Thoughts: A Job Well Done
You’ve successfully removed and reinstalled the glove box in your 2019 Ram 2500! By following these steps, you’ve saved yourself the cost of a mechanic and gained valuable experience working on your vehicle.
What You Need to Know
Q: What if I can’t find the screws holding the glove box lid in place?
A: Some models might have clips instead of screws. Use a small flathead screwdriver or pry tool to gently release these clips.
Q: Are there any other things I need to be aware of when removing the glove box?
A: Be careful not to damage any wiring or connectors while disconnecting them. Also, be mindful of sharp edges on the glove box assembly.
Q: What if I need to remove the glove box for a more complex repair?
A: If you’re dealing with a more complicated repair, it’s always best to consult a qualified mechanic. They have the expertise and tools to handle more complex situations.
Q: Is it difficult to remove the glove box assembly?
A: The process is relatively straightforward. Just follow the steps carefully and be mindful of the wiring and connectors.
Q: Can I remove the glove box without disconnecting the battery?
A: While it’s technically possible, it’s not recommended. Disconnecting the battery is a crucial safety precaution to prevent electrical shocks.