How to Change Tail Light Mitsubishi Adventure: The Ultimate Guide

Are your Mitsubishi Adventure‘s tail lights looking dim, cracked, or even broken? Don’t worry, replacing them is a simple DIY project that can be done in just a few steps. This guide will walk you through the process of how to change tail light Mitsubishi Adventure, from gathering the necessary tools to putting everything back together.

Why You Might Need to Change Your Tail Lights

There are several reasons why you might need to change your Mitsubishi Adventure‘s tail lights:

• Damaged Housing: A cracked or broken tail light housing can compromise the integrity of the light and make it difficult to see.
• Burnt-Out Bulbs: A burnt-out bulb can make your tail lights less effective and can even be a safety hazard.
• Aesthetic Reasons: If you want to upgrade the look of your Mitsubishi Adventure, you can replace the old tail lights with new ones.

Tools and Materials You’ll Need

Before you begin, gather the following tools and materials:

• Replacement Tail Lights: Make sure you purchase the correct tail lights for your Mitsubishi Adventure year and model. It’s a good idea to check your owner’s manual or online for the exact part number.
• Phillips Screwdriver: This is the most common type of screwdriver you’ll need for removing and installing the tail lights.
• Flathead Screwdriver: You may need a flathead screwdriver to pry off some of the trim pieces.
• Socket Wrench: Some tail lights may be secured with bolts that require a socket wrench.
• Work Gloves: These will protect your hands from sharp edges and dirt.
• Protective Eye Gear: Always wear safety glasses to protect your eyes from flying debris.

Step-by-Step Guide to Changing Your Tail Lights

Now that you have everything you need, follow these steps to change your Mitsubishi Adventure‘s tail lights:

1. Park Your Vehicle on a Level Surface and Engage the Parking Brake. This will ensure that your vehicle stays in place while you work.

2. Open the Trunk and Identify the Tail Light Assembly. The tail light assembly is typically located on the rear of the vehicle, near the trunk lid.

3. Remove the Screws or Clips Holding the Tail Light Assembly in Place. Use your Phillips screwdriver to remove any screws or clips that are holding the tail light assembly to the vehicle. Be careful not to strip the screws or damage the surrounding bodywork.

4. Disconnect the Electrical Connector. Locate the electrical connector that plugs into the tail light assembly. Gently pull the connector apart to disconnect it.

5. Remove the Old Tail Light Assembly. Once the screws or clips are removed and the electrical connector is disconnected, you should be able to carefully pull the old tail light assembly out of its housing.

6. Install the New Tail Light Assembly. Align the new tail light assembly with the mounting points on the vehicle and carefully push it into place.

7. Connect the Electrical Connector. Reconnect the electrical connector to the new tail light assembly, making sure it clicks into place securely.

8. Secure the Tail Light Assembly. Replace the screws or clips that you removed in step 3, making sure they are tightened securely.

9. Test the Lights. Turn on your tail lights to make sure they are working properly. If they are not working, double-check the electrical connector and make sure it is properly connected.

Tips for a Successful Tail Light Replacement

• Take Pictures: Before you start, take pictures of the tail light assembly and its wiring harness. This will help you remember how everything goes back together.
• Work in a Well-Lit Area: Make sure you have enough light to see what you’re doing.
• Be Patient: This is a simple repair, but it can take some time, especially if you’re not familiar with car repairs.
• Use the Right Tools: Using the wrong tools can damage your vehicle or the tail light assembly.
• Clean the Area: Before you install the new tail light assembly, clean the area around the mounting points to remove any dirt or debris.

Importance of Replacing Tail Lights

Tail lights are essential for safety. They signal to other drivers when you are braking, turning, or reversing. Replacing faulty tail lights is not just a cosmetic issue, it’s a safety necessity.

Final Thoughts: Keeping Your Mitsubishi Adventure Safe

Changing your Mitsubishi Adventure‘s tail lights is a simple and affordable way to keep your vehicle safe and looking its best. By following the steps outlined in this guide, you can easily replace your tail lights yourself and avoid the cost of a mechanic. Remember, safety is paramount, so don’t hesitate to seek professional help if you feel uncomfortable performing the repair yourself.

What You Need to Know

Q: How do I know if my tail light bulbs are burnt out?
A: If one or more of your tail lights are not working, the bulb may be burnt out. You can check this by turning on your tail lights and inspecting the bulbs. If they are not lit up, they are likely burnt out.

Q: Can I use any type of tail light bulb for my Mitsubishi Adventure?
A: No, you need to use the correct type of bulb for your Mitsubishi Adventure. The bulb type is usually listed in your owner’s manual or on the old bulb itself.

Q: How often should I replace my tail lights?
A: There is no set schedule for replacing tail lights. However, you should inspect them regularly for signs of damage or wear. If you notice any cracks, chips, or burnt-out bulbs, you should replace them immediately.

Q: What if I can’t find the correct tail light assembly for my Mitsubishi Adventure?
A: If you can’t find the exact tail light assembly for your Mitsubishi Adventure, you can contact a local auto parts store or online retailer. They should be able to help you find the correct part.